Halloween Cards and Treat Holder

 

 

Hello Stampers.

Here are 2 Halloween cards that I recently made

at my last card class.

The first card is using the stamp set SPOOKY CAT #144749.

And the CAT PUNCH #144666.

You can also purchase these as a bundle and save 10% #146014.

THE INGREDIENTS ARE AS FOLLOWS:

I used a piece of Basic Black Cardstock #121045 cut at 4 1/4 x 11.  Scored at 5 1/2.

Daffodil Delight #119683 cut at 4 1/8 x 5 3/8 and 4 x 5 1/4 (for inside of card)

Basic Black Cardstock #121045  cut at 4 x 5 1/4.

Punch a piece of Very Vanilla Cardstock #101650 with the

2 1/4 Circle Punch #143720.

Sponge circle with Daffodil Delight ink pad #126944.

Insert the Very Vanilla circle into the Cat Punch and punch

just above the cats feet.

Using the moon and start thinlit from The Card Front Builder #144674

position it towards the top of the black cardstock and

run it through the Big Shot #143263.

Using adhesive of your choice adhere Black cardstock to the

Daffodil Delight cardstock.  I used some twine that I had leftover

from the last years holiday catalog.  Wrapped around card 3 times and made a bow.

Stamp Happy Halloween on a piece of Daffodil Delight that measures 3/4 x 3 1/2.

Using Paper Piercing Snips #103579 pennant the ends and adhere to card with

Stampin Demensionals #104430.

Adhere Daffodil Delight to Black card base and the Daffodil Delight cardstock

to the inside of the card.

 

The next card is also made using the Spooky Cat Bundle #146014 and the

Spooky Night DSP #144610.

THE INGREDIENTS ARE AS FOLLOWS:

Basic Black Cardstock #121045 cut at 4 1/4 x 11 scored at 5 1/2.

Night of Navy Cardstock #100867 cut at 4 x 5 1/4.

Very Vanilla Cardstock #101650 cut at 3 7/8 x 5 1/8.

Another piece of Very Vanilla Cardstock cut at 4 x 5 1/4 for the inside of card.

Smokey Slate #131202 cut at 3 7/8 x 2 1/4.

First thing I did was use the Embossing Paste #141979 and the

Cherry Cobbler reinker #119788. Put some of the embossing paste

on a paper plate and add a few drops of the cherry cobbler reinker

Mix together using the Palette Knives #142808.

Using the Brick Stencil from the Pattern Party Decorative Masks #144103

Place on top of the Smokey Slate cardstock.

Using one of the Palette Knives spread the embossing paste on the stencil.

Peel of stencil and wash IMMEDIATELY. The paste dries quickly.

Set Smokey Slate cardstock aside to dry.

Using the smaller piece of very vanilla I started sponging 3/4 of the way down.

I first used Daffodil Delight #126944 then Pumpkin Pie #126945. Blending the colors together.

Next is Rich Razzleberry #126950 then Night of Navy #126970.

Blending those colors as well.

Then using the Wink of Stella Glitter Brush #141897 tap it against your finger

over the sponged area to make it look like a starry night.

Using a scrap piece of very vanilla cardstock punch out a circle using the

2″Circle Punch #133782.  Sponge circle using Daffodil Delight ink #126944.

Using the Spooky Night DSP punch out one black cat using the cat punch.

Check to see if the embossing past is dry.  When dry adhere to the sponged cardstock.

Then using the Vintage Crochet Trim #144611 wrap around card at the top of the wall.

Attach moon and cat to the card.  Attach that piece to the Night of Navy cardstock.

Then attach that piece to the Basic Black cardstock base.

Add piece of Very Vanilla cardstock to inside of card.

I also used 4 Rhinestones #144220 to make a collar for the cat.

Here is a little Halloween treat that one of my customers Therese Wilmot gave to me.

Isn’t it cute?

Happy Halloween!